Can you fill it with Cheez Whiz, and then lay your head in it with your mouth open?
Wolf's Den
- Thread starter Wolf
- Start date
Can you fill it with Cheez Whiz, and then lay your head in it with your mouth open?
I appreciate it!
I did buy couple of upgrade parts. Like yellow springs and better gears for the heat bed. I'm waiting for Amazon to deliver them.
My son says the Ender 3 v2 is "the best one".
The bed wobble "is completely normal, it's due to the tensioning springs being compressed when you wiggle the bed plate. That doesn't happen while it's printing. Just make sure you have a spring under each of the four corners of the print bed."
For the arm having a hard time going back up "this is normal. It doesn't prevent the printer from working but it sucks for calibration. If you want you can loosen these two screws, but only a little bit. It doesn't have to be half out. Maybe a half-turn."
For the right side z-axis passive block wheels, "I'm guilty of having that loose too but it's never been a problem. But if you want to fix that, try tightening this screw. Thanks for remind ME to tighten that one."
View from the back, behind the power supply....
Thanks for your suggestions @sadchild. I was able to get the heat bed wobbly issue resolved. The eccentric spacers needed tightening and same for the V slot. I was able to power it on and get everything set up. Later today I will do my first test print.
When I turned the unit on, I took a quick pic and then placed the heat bed glass with bed clips.
When I turned the unit on, I took a quick pic and then placed the heat bed glass with bed clips.
My son says, "Wow I didn't realize my eccentric spacers under the bed needed to be adjusted. I didn't realize that was a thing until you brought it up."
I saw a video over the weekend where a guy printed a guitar neck that actually worked.
Kinda trippy. I printed a couple of building models a few years ago. Fun stuff.
Kinda trippy. I printed a couple of building models a few years ago. Fun stuff.
Last night, I officially did my first test print and this was the outcome.
I adjusted the heat bead closer to the nozzle and this was the final product.
Here's a video of it partly in action.
I adjusted the heat bead closer to the nozzle and this was the final product.
Here's a video of it partly in action.
Charlotte FC did break the all-time attendance record for an MLS match last weekend.
It's so sad to see how this group of Americans can be so misguided. Maybe one day they'll get their lives back on track.
They should all be heading to a Phish concert. Or an episode of The Bachelor.
Wolf are you currently on fire?
www.dailymail.co.uk
Thousands evacuate as Arizona's Tunnel Fire explodes to 6,000 acres
A towering 'wall of fire' whipped by high winds is forcing thousands to evacuate an Arizona tourist town, as Red Flag warnings for high-risk weather conditions cover much of the Southwest.
Who could ever imagine that a place as hot and dry as hell on earth would have wildfires?Wolf are you currently on fire?
Thousands evacuate as Arizona's Tunnel Fire explodes to 6,000 acres
A towering 'wall of fire' whipped by high winds is forcing thousands to evacuate an Arizona tourist town, as Red Flag warnings for high-risk weather conditions cover much of the Southwest.
And BTW, there's a thread for that
Wildfires
If anyone in the Midwest states has been smelling smoke or your skies been hazy, it because Arizona has a very bad wildfire going on. It called the Wallow wildfire and it the 3rd largest wildfire in state hirstory. So far the blaze has blackened nearly 234,000 acres or 364 square miles of...
digitalradiocentral.com
Last edited:
How dare you!?!
This is the correct thread. I was asking if specifically Wolf, the man, is currently of fire. Not if there are wildfires in his area right now.
I just wanted to make sure he remembered to stop, drop and roll if that happened to be his current situation.
